How To Remove Dsi Battery

Introduction

This guide has been updated by iFixit staff! Read the new, official guides hither and here.

A guide on how to remove the unabridged Nintendo DSi instance.

• Loosen the two screws on the battery console. Then lift the panel up to remove it.



• Fifty Button.

• Meridian of the battery pack.

• To remove the battery pack, place your fingernail or a spudger at the top of the bombardment near the Fifty button. Gently elevator the battery out.

• Two screws are hidden underneath two condom anxiety highlighted in red.

• Use the tip of a spudger to pry the rubber feet out of the lower case.

• Remove the following screws securing the lower instance to the body of the DSi:

• Vi 5.ii mm Phillips #00 screws.

• I 2.seven mm Phillips #00 spiral.

• Insert the spudger in betwixt the lower casing and lower panel virtually the pinnacle right corner of the DSi.

• Advisedly run the spudger along the edge of the outer casing, creating an opening between the trunk and the casing.

• Go along running the spudger effectually the trunk of the DSi until the majority of the lower case has been separated.

• Advisedly lift the lower casing from its bottom edge.

• The lower case is all the same attached to the motherboard past the book and SD lath cable highlighted in blood-red. Exercise not endeavour to completely remove the lower example of the DSi however.

• Pry the volume and SD lath cablevision up from its socket on the motherboard using a spudger.

• Once the cable is completely removed, then you lot may take off the entire outer casing.

• Flip up the black latch and disconnect the D-Pad/Power Button ribbon cablevision.

• The power connector (with red and blackness wires) is hard to remove without dissentious it, unless you take a moment and understand how it works. Wait at all of the photos for this stride before continuing.

• The connector is two pieces -- a white "male" piece (connected to the wires), and a biscuit "female" office (soldered to the chief board).

• There is a small-scale "notch" in the female part, to give you lot a place to insert a small flat-head screwdriver. Put the corner of your screwdriver in there, and twist it gently to push the white role up (abroad from the master board). Do not try to pull information technology to the correct (towards the battery board).

• If information technology does not lift easily, try again with a smaller screwdriver. Y'all might be pulling the female connector off the board, which will be difficult to repair.

• Remove 4 Phillips screws from the board.

• Lift the master board from the lesser end and flip it over to reveal the terminal connector.

• Go on the main board fairly close to the example, making sure not to damage the terminal ribbon cable holding information technology in place.

• Disconnect the ribbon cable by gently using a plastic opening tool to flip upwardly the black connector latch. The cablevision should easily slide out from the connector.

• The motherboard should now be gratuitous from the rest of the device.

• Remove the safety front-panel button membranes from the device. Pay careful attention to where the buttons go, and so you lot tin supervene upon them correctly.

• A/B/10/Y push assembly

• Select/Start push button associates

• D-pad

• Ability push button

• Remove the plastic buttons and keep them in a safe place.

• All of the buttons take "primal" notches to prevent them from being inserted incorrectly (backwards or in the wrong place), but it can have a while to figure out where everything goes if they get shuffled around.

• Flip the case open up, and push the lower screen associates out of the frame.

• To make the repair easier, nosotros recommend removing the bottom LCD screen prior to replacing the meridian LCD screen.

• Using a spudger, or similar tool, pry out the 4 square screw covers.

• Remove 4 Phillips screws with a #00 Phillips screwdriver.

• Identify a plastic opening tool between the front panel and meridian border of the outer case. Slide the tool along the border as needed to prop open up the instance.

• With the screen facing you, slide the screen side down with your thumbs to dissever the screen from the cover.

• Remove the antenna from the lesser left of the device.

• Remove the microphone from the top of the frame.

• Utilize a spudger to pry the camera out of its identify.

• Cables for the components in the upper half of the device run through the hinge, which must be carefully disassembled before continuing.

• Outset by pushing the sliding shaft in the hinge on the opposite side of the wires/ribbons.

• On the reverse side of the casing, insert the spudger onto the surface of the sliding shaft only left of the LED low-cal channels.

• Push the sliding shaft completely through the hinge until it stops and the hinge is released.

• The right side of bottom case should separate from the summit case when you lot remove the sliding shaft.

• Do not pull up too far or the wire swivel may be damaged.

• Slide the top case to the correct to dissever the articulation.

• Weave the wires and ribbons through the wire swivel to completely carve up the superlative and lesser casings.

• The speakers are soldered to the ribbon cablevision attached to the upper LCD, then they must be removed at the same time as the LCD.

• Lift the top LCD out of the plastic frame. Carefully thread the ribbon cable out of the swivel to avoid damaging it.

• To remove the speakers, place a flat object underneath and gently pry them off.

• On the bottom cover, apply a screwdriver to remove the iii Phillips screws property the bombardment compartment.

• Removing the 2 lower screws besides removes the "Fifty" trigger.

• The "L" trigger has a spring backside its eye and a small metal axle in its joint.

• Use a small tool to pry the bombardment compartment off the bottom cover.

• Employ a screwdriver to remove the 5 screws on the stylus holder.

• Likewise disconnect and remove the "R" trigger button, which is held in place past two of the five stylus holder screws.

• The "R" trigger has a jump behind its center and a small metal axle in its joint.

• Under the stylus holder is the SD bill of fare port.

• Gently elevator the SD card port off the bottom cover.

• Remove the metal shield and flap from under the SD carte du jour port.

• This picture shows the LCD screen, bombardment compartment, and SD card slot (metallic shield and flap) with bottom outer casing.

• The consummate DSi outer casing tin now be replaced. Parts listed left to right: top embrace, top LCD screen casing, touch LCD screen casing, and bottom comprehend.

• Follow the guides for the replacement of the DSi components backwards with your new outer casing.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Team

Embed this guide

Choose a size and re-create the code below to embed this guide equally a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/Nintendo+DSi+Outer+Casing+Replacement/1399

Share this post